Page 1 of 2

Will VDOEditor work on 5N0920883C?

Posted: 09 Aug 2016 17:34
by pawelluk
Hello,

Before I purchase the editor, I would like to know if it will work on the following cluster:
5N0920883C
SW: 0611

I would like to enable side asist.

Thank you!

Re: Will VDOEditor work on 5N0920883C?

Posted: 09 Aug 2016 22:05
by skodapilot
This cluster is not whitelisted, but I did not see any problem to do it. Since version 1.0.2.1 I fixed some problem with activation of SA on SW06XX.
Even more, I could guarantee for money back if this feature will not work. Of course, You can wait for response from other users

Re: Will VDOEditor work on 5N0920883C?

Posted: 25 Aug 2016 00:44
by didlina77
Sw06xx should support side assist

Re: Will VDOEditor work on 5N0920883C?

Posted: 29 Jan 2017 19:55
by blue0814
Its offtopic, but I'm searching for a dump of a 5N0920883C with SW 0611

Maybe someone can upload one or sent me a PM.
Thank you!

Re: Will VDOEditor work on 5N0920883C?

Posted: 02 Feb 2017 11:29
by skodapilot
blue0814 wrote: 29 Jan 2017 19:55 Its offtopic, but I'm searching for a dump of a 5N0920883C with SW 0611
I have data from 883B SW05XX , 883D SW07XX and 883F/G SW10XX only

Re: Will VDOEditor work on 5N0920883C?

Posted: 02 Feb 2017 16:44
by blue0814
Thanks for your reply
That's not what I'm looking for. But maybe I can make an new with all in one :)

It would very well if you sent me one copy of all 4 dumps.

Thank you!

Re: Will VDOEditor work on 5N0920883C?

Posted: 09 Dec 2018 20:37
by pawelluk
Hi,

Its been a while but wanted to post an update.

Got side assist working except for the LED. So I have side assist in the menu and can select to turn it OFF or ON.

I did also install the LEDs and resistors, tested by changing panel layout from VW v0.1 hex 07 to VW v0.3 hex 05, which showed LED working.

So my question is, would it be a SW issue or is there another configuration bit that needs to be triggered in EEPROM?

Is there an EEPROM configuration that enables all of the LEDs to work and display status?

On a separate note, could someone send me a 300km/h reference bin?

Thank you!

Re: Will VDOEditor work on 5N0920883C?

Posted: 09 Dec 2018 20:47
by skodapilot
Dumps are available over our VDO EEPROM database here: https://osotec.com/vdo/dumps

Re: Will VDOEditor work on 5N0920883C?

Posted: 09 Dec 2018 22:40
by Daku
Hi i have 5n0 920 883C sw 0611
This cluster doesnt have mounted sideassist led and resistors at factory

VDO can enable it

I flashed thos cluster to another car and it works. You can try to flash it to newer version e.g 3d

But if i remember i put it in my car with soldered and enabled SA and all works.

Re: Will VDOEditor work on 5N0920883C?

Posted: 10 Dec 2018 21:20
by pawelluk
Thank you skodapilot and Daku!

Daku, could you possibly send me the firmware you used?

Is there a good place where someone could buy instrument cluster parts? I was looking for a new instrument cluster case, or just the see through clear plastic lens for a Jetta Mk6.

Thanks!