Hello All,
I would like ask you have i can configure vaghelper for US lights ( Front turn lights with brightness 30% + 100% for turn signal ) ?
I dont really understand how i can configure 2 different brightness for example for A10,C50 (turn front L+R).
thanks a lot for help.
Dear new users!
All messages from new users are moderated by administrator. Keep patience if You first message is not published, You will see it as soon as it will be accepted. Additional, new users have restriction in using of private message system.
All messages from new users are moderated by administrator. Keep patience if You first message is not published, You will see it as soon as it will be accepted. Additional, new users have restriction in using of private message system.
US lights for octavia 2 FL
-
- Site Admin
- Posts: 464
- Joined: 13 Jan 2014 06:18
Re: US lights for octavia 2 FL
As far as I remember, It should be coded like this
Unlike MQB, you code only one brightness due to second is always 100%-
- Posts: 6
- Joined: 04 May 2019 15:45
Re: US lights for octavia 2 FL
ok i will try it, where i can found some manual for vaghelper ? I am still dont understand of logic for it.
When i marked in function turn signal, park lights and daytime running lights and brightness will be 33% so for what will be 100% brightness?
When i marked in function turn signal, park lights and daytime running lights and brightness will be 33% so for what will be 100% brightness?
-
- Site Admin
- Posts: 464
- Joined: 13 Jan 2014 06:18
Re: US lights for octavia 2 FL
I don't understand fully too, even I'm developer. It is not joke. VAGHelper is result of reverse engineering. There are several blind spots
-
- Posts: 6
- Joined: 04 May 2019 15:45
Re: US lights for octavia 2 FL
ok no problem i am testing it . Nevetheless US lights working as expected. thanks .
-
- Posts: 6
- Joined: 04 May 2019 15:45
Re: US lights for octavia 2 FL
today i tried to test US lights at passat b7 2010. Same procedure as for Octavia 2 FL but it doesnt work. I configured A10(front turn signal) for 33% but after write configuration to ecu ligthning turn front signals with 100% brightness . So i dont understand of logic of program. Can you help me with it ?
Do you need screen of BCM or something ?
Do you need screen of BCM or something ?
-
- Site Admin
- Posts: 464
- Joined: 13 Jan 2014 06:18
Re: US lights for octavia 2 FL
Are You sure that value is applied? What about 18th byte of long coding?
-
- Posts: 6
- Joined: 04 May 2019 15:45
Re: US lights for octavia 2 FL
What was changed is just that turn signal lighting at 100%. I will check later autoscan how was set up bit18. it should be 00 ?
-
- Site Admin
- Posts: 464
- Joined: 13 Jan 2014 06:18
-
- Posts: 6
- Joined: 04 May 2019 15:45
Re: US lights for octavia 2 FL
output from autoscan. If i am counting right , that byte 18 is 00
Address 09: Cent. Elect. (J519) Labels:. 3AA-937-087.clb
Part No SW: 3AA 937 087 B HW: 3AA 937 087 B
Component: BCM PQ47 H+ 413 0452
Revision: BC413001
Coding: 000000000000000000180080140029F463D50088606C8160E480C7240041
Shop #: WSC 05311 000 00000
VCID: 392ED8D8E953009F993-806C
Subsystem 1 - Part No SW: 3AB 955 419 HW: 3AB 955 419 Labels: 1KX-955-119.CLB
Component: Wischer 14021 10 0603
Coding: 00B795
Subsystem 2 - Part No: 1K0 955 559 AH Labels: 1K0-955-559-AG.CLB
Component: RLS 140311 05 54 0403
Coding: 033028
So that was configured well.
Address 09: Cent. Elect. (J519) Labels:. 3AA-937-087.clb
Part No SW: 3AA 937 087 B HW: 3AA 937 087 B
Component: BCM PQ47 H+ 413 0452
Revision: BC413001
Coding: 000000000000000000180080140029F463D50088606C8160E480C7240041
Shop #: WSC 05311 000 00000
VCID: 392ED8D8E953009F993-806C
Subsystem 1 - Part No SW: 3AB 955 419 HW: 3AB 955 419 Labels: 1KX-955-119.CLB
Component: Wischer 14021 10 0603
Coding: 00B795
Subsystem 2 - Part No: 1K0 955 559 AH Labels: 1K0-955-559-AG.CLB
Component: RLS 140311 05 54 0403
Coding: 033028
So that was configured well.
Who is online
Users browsing this forum: No registered users and 1 guest