Page 1 of 2

US lights for octavia 2 FL

Posted: 04 May 2019 15:50
by rrozbroj
Hello All,
I would like ask you have i can configure vaghelper for US lights ( Front turn lights with brightness 30% + 100% for turn signal ) ?
I dont really understand how i can configure 2 different brightness for example for A10,C50 :) (turn front L+R).
thanks a lot for help.

Re: US lights for octavia 2 FL

Posted: 04 May 2019 17:50
by skodapilot
As far as I remember, It should be coded like this
Hidden Content
This board requires you to be registered and logged-in to view hidden content.
Unlike MQB, you code only one brightness due to second is always 100%

Re: US lights for octavia 2 FL

Posted: 04 May 2019 18:53
by rrozbroj
ok i will try it, where i can found some manual for vaghelper ? I am still dont understand of logic for it.

When i marked in function turn signal, park lights and daytime running lights and brightness will be 33% so for what will be 100% brightness?

Re: US lights for octavia 2 FL

Posted: 04 May 2019 22:38
by skodapilot
I don't understand fully too, even I'm developer. It is not joke. VAGHelper is result of reverse engineering. There are several blind spots

Re: US lights for octavia 2 FL

Posted: 04 May 2019 22:41
by rrozbroj
:) ok no problem i am testing it . Nevetheless US lights working as expected. thanks .

Re: US lights for octavia 2 FL

Posted: 14 May 2019 16:05
by rrozbroj
today i tried to test US lights at passat b7 2010. Same procedure as for Octavia 2 FL but it doesnt work. I configured A10(front turn signal) for 33% but after write configuration to ecu ligthning turn front signals with 100% brightness . So i dont understand of logic of program. Can you help me with it ?
Do you need screen of BCM or something ?

Re: US lights for octavia 2 FL

Posted: 15 May 2019 09:42
by skodapilot
Are You sure that value is applied? What about 18th byte of long coding?

Re: US lights for octavia 2 FL

Posted: 15 May 2019 11:08
by rrozbroj
What was changed is just that turn signal lighting at 100%. I will check later autoscan how was set up bit18. it should be 00 ?

Re: US lights for octavia 2 FL

Posted: 15 May 2019 12:23
by skodapilot
rrozbroj wrote: 15 May 2019 11:08 What was changed is just that turn signal lighting at 100%. I will check later autoscan how was set up bit18. it should be 00 ?
yes. Due to it acts as pointer. If you change this value, other addresses are used by BCM to configure light scheme

Re: US lights for octavia 2 FL

Posted: 16 May 2019 20:10
by rrozbroj
output from autoscan. If i am counting right , that byte 18 is 00

Address 09: Cent. Elect. (J519) Labels:. 3AA-937-087.clb
Part No SW: 3AA 937 087 B HW: 3AA 937 087 B
Component: BCM PQ47 H+ 413 0452
Revision: BC413001
Coding: 000000000000000000180080140029F463D50088606C8160E480C7240041
Shop #: WSC 05311 000 00000
VCID: 392ED8D8E953009F993-806C

Subsystem 1 - Part No SW: 3AB 955 419 HW: 3AB 955 419 Labels: 1KX-955-119.CLB
Component: Wischer 14021 10 0603
Coding: 00B795

Subsystem 2 - Part No: 1K0 955 559 AH Labels: 1K0-955-559-AG.CLB
Component: RLS 140311 05 54 0403
Coding: 033028

So that was configured well.